SAE J1100 PDF

SAE J This standard provides a system of a defined nomenclature to describe vehicle dimensions. A. combination of letters and numerals helps the. This SAE Recommended Practice defines a set of measurements and standard procedures for motor vehicle dimensions. The dimensions are primarily intended . 26 May BY ORDER OF THE EXECUTIVE DIRECTOROffice of the Federal RegisterWashington, Authority of the Code of Federal Regulations.

Author: Kajilar Kajit
Country: Pacific Islands
Language: English (Spanish)
Genre: Photos
Published (Last): 11 January 2012
Pages: 107
PDF File Size: 15.79 Mb
ePub File Size: 13.26 Mb
ISBN: 555-4-45144-998-1
Downloads: 77961
Price: Free* [*Free Regsitration Required]
Uploader: Kegor

Simulates the position of the Pivot Center of the human torso and thigh, and d. W3 Shoulder room – front 6.

The front wheels shall be positioned in the straight-ahead position. If the depressed pedal is used, the ase must be flat on the accelerator pedal. Measure the same as H Each dimension is assigned a code which is composed of a prefix sae j1100 swe the direction or type sae j1100 dimension and a number issued in sequence as required by each sae j1100 letter. Foremost-Lowest Design H-Point— The foremost location of the full down position of vertical travel independent of track rise.

W16 Cushion width – front 6.

Full text of “SAE J Motor Vehicle Dimensions”

See Figures sae j1100, 7, 9, and Hi1 Entrance height – front 6. The upward angle sightline is at 7 degrees tangent to the upper sae j1100 of the eyellipse while the downward angle sightline is at 5 degrees tangent to the lower portion of the eyellipse. Independent vertical adjustment, if provided, is not included.

If there is no second step, the dimension will be sae j1100 the top of the sill plate bead at the sae j1100 of the lower door opening. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user. The Torso Line is parallel to the straight flat portion of the lower back on the torso and is used to facilitate the definition of torso angle. All interior dimensions for designated seated positions are defined on the Y-plane centerline of the occupant, unless otherwise defined in the dimensions definition.

Related Posts  4506T BANK OF AMERICA DOWNLOAD

For rear-facing third seat, measure from the trimmed seat back at a sae j1100 tangent to the top of the third Seat Cushion surface, rearward to the interior tailgate closure. The foot may be placed on the floor pan with the centerline of the leg segment up to mm either side of the Y plane occupant centerline. They sae j1100 be loosened and moved to the limits of the attaching hardware and then retightened to attain the most advantageous position.

H70 SgRP – front – Z coordinate 6.

See j110 Figures 27 sae j1100 If the symbol is next to the report title, it indicates a complete revision of the report. For heavy-duty trucks, suspension seats will be positioned as specified by the vehicle manufacturer in the normal driving position with any fore and aft isolator locked out. Steering wheel shall be sae j1100 with front wheels in straight-ahead position.

Criminal penalties may apply for noncompliance.

L Sae j1100 body overall length 8. SAE invites your sad comments and suggestions. X, Y, Z coordinates are dimensioned to their respective planes. See H70, L31and W Any portion of this mm by mm area around the SgRP in side view below and behind the seat cushion and seat back trim is excluded. The dash panel is usually the vertical extension of the toe panel.

Reference points defining Sad travel path are as follows: NOTE— The steering column center is used instead of the wheel center to eliminate error that could occur sae j1100 a non-symmetrical Steering Wheel. When j11000 one outside mirror sae j1100 standard, the dimension will be to the zero “Y” plane.

Foremost-Highest Design H-Point— The foremost location of the full up position of vertical travel independent of track rise.

SAE J1100: Motor Vehicle Dimensions

GVWR is the value specified by the vehicle manufacturer as the loaded weight of a single vehicle. If the seatback is adjustable, use the normal driving and sae j1100 position specified by the manufacturer. Design H-Point Travel Path Definition Revised Section No. Their location is specified in the three-dimensional reference system sae j1100 X, Y, Z coordinates and to ground, with the vehicle at a specified Vehicle Weight.

Related Posts  PUROHIT DARPAN EPUB

A piece from the Standard Luggage Set may be removed xae place an H-box in the sae j1100, provided the removed piece is replaced.

Luggage Capacity — Passenger car enclosed Luggage Compartments including hatchbacks and station wagons partitioned to secure j11000 cargo V1 – Luggage Capacity Total of volumes of individual pieces of standard luggage set plus H-boxes stowed in the Luggage Compartment in accordance with the procedure described in 9. W width and H height codes to denote specific pedal dimensions. All other adjustable features, such as an adjustable steering wheel and adjustable seat height, a seatback that adjusts independently from the Seat Cushion, power 4-way or 6-way seats, etc.

The forward limit is the rear side sae j1100 the sae j1100 seatback or sae j1100 folded third seat. If no arm rest is provided at the designated “X” plane, use a sae j1100 of 1 80 mm above the SgRP.

sae j1100 H Zero Z plane to ground sas front 7. The forward limit is the rear side of rear of the front seatback, and a vertical plane tangent to and extending above the front seatback. Sae j1100 minus – dimension indicates that the brake pedal j110 lower than the accelerator pedal. Establishes the rearmost normal design driving or riding position of each designated seating position which includes consideration of all modes of adjustment, horizontal, vertical, and tilt, in a vehicle, b.