ArcWear performs vertical flame testing for textiles in accordance with ASTM D which is used in ASTM F, ASTM F, and NFPA We will report. 23 Jul Some updates have been made to ASTM D Standard Test Method for Flame Resistance of Textiles (Vertical Test) commonly used in flame. ASTM D Test Method for Flame Resistance of Textiles. (Vertical Test). • Pass criteria: max char length of 10 cm. • After-flame of not more than 2 seconds.

Author: Niran Tygoll
Country: Yemen
Language: English (Spanish)
Genre: Business
Published (Last): 9 March 2012
Pages: 320
PDF File Size: 15.95 Mb
ePub File Size: 5.77 Mb
ISBN: 851-2-71515-174-3
Downloads: 55900
Price: Free* [*Free Regsitration Required]
Uploader: Dozuru

July 10, at 9: Save my name, email, and website in this browser for the next time I comment. Five tests are performed and the results are averaged and astm d6413 as the final test result. The astm d6413 results from the two laboratories should be compared using a statistical test for unpaired data, at d64113 probability level chosen prior to the testing series.

NFPA 2112 – ASTM D6413: Vertical flame test method

The ASTM D test method is utilized to evaluate the flame resistance of every astm d6413 lot of fabric used in Tyndale-branded clothing. Notify me of new posts by email. Char Length is the length in inches of fabric destroyed by the flame. This is the defining test method for compliance with OSHA Adopted astm d6413 Federal Test Standard No.


If a bias astm d6413 found, either its cause must be found and corrected, or future test results must be adjusted in consideration on the known bias. Your email address will not be published. Historical Version s – view previous versions of standard.

Referenced Documents purchase separately The documents listed below d64133 referenced within the subject standard but are not provided as part of the standard. Combining values from the two systems may result in non-conformance with astm d6413 standard. ASTM D is used to determine flame resistance of fabrics used to protect against both electric arc and flash fire hazards. The occurrence of melting or dripping, if any, astm d6413 also recorded.

ASTM D / DM – 15 Standard Test Method for Flame Resistance of Textiles (Vertical Test)

Garments that meet these standards are used to comply with: The values stated in astm d6413 system may not be exact equivalents; therefore, each system shall be used independently of the other. Refer to Section 14 for single-laboratory precision.

Afterglow is the number of seconds during which there astm d6413 a visible glow remaining on the fabric.

As a minimum, the test samples used should be as homogeneous astm d6413 possible, that are drawn from the material from which the disparate test results are obtained, and that are xstm randomly in equal numbers to each laboratory for testing. The between-laboratory precision of this test method has not been established. The cut edge of the fabric on the bottom is exposed to a controlled methane flame for 12 seconds as seen in the image above, left. Astm d6413 is the responsibility of the user of d641 standard to establish appropriate safety and health practices and determine the astm d6413 of regulatory limitations prior to use.


Afterflame is the number of seconds during astm d6413 there is a visible flame remaining on the fabric. We are Proud to Protect workers, and understand that our dedication to testing is the only way to ensure that our garments perform as expected — every time!

Leave a Reply Cancel d64113 Your email address will not be astm d6413.

Tyndale performs voluntary safety auditing on D6143 garment fabrics. ICS Number Code Link to Active This link will always astm d6413 to the current Active version of the standard.

Notify me of follow-up comments by email. After exposure to the flame, afterflame, afterglow astm d6413 ashm length are measured: Other materials with established test values astm d6413 be used for this purpose. The purpose of this test is to determine whether a fabric will continue to burn after the source of ignition is removed. Work Item s – proposed revisions of this standard.